The Handyguys discuss what nailer you use when. A pneumatic nailer takes much of the work or of driving nails and saves you time. With one pull of the trigger the nail is set flush or below the surface of the work. Nailers allow for one handed operation which frees up your other hand for positioning the work. A nailer can also get into tight or awkward locations where it would be virtually impossible to swing a hammer. There are nailers for interior trim, crown molding, chair rail, craft projects, woodworking, framing, building a deck or roofing. There are many many specialty nailers designed for specific jobs.

In this show we address a few questions about nailers from one of our fans Eddie. Eddie wrote us and asked.

I am doing a complete kitchen remodel as you may remember. To help me in this I got a set of 4 Campbell Hausfeld nail guns from Lowe’s. Now my dad owned nail guns and I saw him use them. But I was never allowed to use them very much and don’t know much about them. ( I know they are dangerous and that you have to oil them, usually with an oiler place in line on the air hose)

I need a resource for learning about these machines and the finer points of using them. What kind of maintenance etc. what kind of nails they are capable of using ( are there just one or two sizes per gun?) When do I choose which gun? I have some common sense but don’t have enough experience or education to know what question to ask.

This is quite a question! Eddie, we have dedicated this entire show to your questions. You asked the right questions.

First a run down of the most common nailguns

Maintenance

Most pneumatic nail guns need to be oiled. You mention an in-line oiler. This option probably didn’t come with your kit. They can be added to facilitate automatic oiling of your tools. The disadvantage is you will have oil in your hose which is really bad if you are going to use the compressor for spraying paint. Most people will usually just add a few drips of tool oil in the air inlet before using the tool.

Safety

Be sure to read an follow all the instructions that came with your kit. Safety glasses are a must.

Tip!!

Paul had a really random tip to wrap up the show. Door stoppers, get the spring loaded ones, not the solid ones. You have to listen to the show to understand why.

Related shows:

1. Homeowner Air Compressor Tips
2. Using a Pneumatic Nailer for Target Practice
3. Buying Reconditioned Tools

Do you need to bend sheet metal? A "Brake" is the right tool foor the job. Click image to see full size.

In this show we address a couple of listener questions about mower blades and metal brakes and then talk about another expensive DIY mistake.

First up is a question from David:

Do you guys have or know of any plans for a DIY metal brake? I need to cover the sills of my home windows, and would like to have a brake to bend the aluminum nicely myself.

Thanks, David

David, we are not familiar with any decent DIY brake plans. A brake is a specialized tool for bending metal. There is certainly no better tool for covering your sills with metal flashing. We recommend that you try and borrow one or rent this tool. A brake requires some practice but once you get the hang of it you can make some nice capping for your window sills and trim.

We also got this question from Vishal:

What tools do you need to loosen/tighten a lawn mower’s blade?

Short answer – a wrench. Is that really the question though? The Handyguys discuss how to keep the blade from spinning when you remove the bolt and how to apply a little more leverage if the bolt is stuck. Also why do we remove a mower blade anyway? Blades require sharpening, balancing and outright replacement from time to time.

We covered sharpening blades and other basic tuneup tips in Episode 14, give it a listen.

Expensive DIY Mistakes

The Handyguys discuss another expensive DIY mistake

Whats the mistake? Paying twice. Why would you pay twice? If you underestimate your abilities, do a job poorly, and need to pay a pro to come in and do it correctly. Perhaps the mistake is really not knowing your abilities. The handyguys discuss how to avoid this costly mistake.

For this and more, give a listen to the podcast.

Related shows:

1. How to sharpen a mower blade video
2. Avoiding Costly DIY Mistakes
3. How To Cut Metal, CFL Safety And Water Saving Flush Valves

This unique, high quality, floor was installed by Handyguy Brian. Listen to the podcast for details.

The Handyguys tackle hard wood flooring.

The Handyguys would like to thank A to Z Exotic Hardwoods for sponsoring this episode. They specialize in procuring the worlds most beautiful woods. With a virtually unlimited palette of colors and figures in native American as well as imported species, they can use the warmth and radiance of real woods to customize your interior projects

Steve asked:

Hey Handyguys… awesome shows.  I am planning to replace my carpets on the first floor of my house with hard wood flooring.  However, when I began to research hard wood flooring I learned that there are many kinds of “hard wood” flooring.  There are laminate floors, pre-finished floors, pre-engineered hardwoods and traditional solid hardwood planks.  And then there are laminate floors that use “fake” wood.  Please let me know what kind of wood flooring I should use on the first floor of my house including the kitchen.

There are many choices in wood flooring especially since resellers are marketing wood from all over the world.

Your floors should be flat, clean and stable before installing hardwood. Listen to the podcast for an overview of the install process.

Let’s define your choices:

Laminate flooring.  Several companies make laminate flooring that is uses particle board (or similar) as a base and then a top layer that is not necessarily wood.  It is made to look like wood.  This flooring is generally put down in sections that are glued or snapped together.

Brian does not like this flooring for reasons that may surprise you. Listen to the podcast to find out why.

Engineered flooring.  This flooring typically uses a plywood base with a layer of real wood on the top.  This wood has some benefits for installation and stability and can have a tough finish.  It can be pricey though.

Traditional Hard wood flooring.  This is typically 3/4″ thick.  You have lots of choices from around the globe.  The installation will require a nailer and you have a choice between non-finished and pre-finished.

So what kind of floor should the handyguy purchase and install? And how do you install it?  Listen to the podcast for our recommendations.

The Handyguys would like to thank A to Z Exotic Hardwoods for sponsoring this episode. The images below are just a few of their customers floors. Click on the banner to visit their site and contact them if you want hardwood floors. Click each image to see a larger view.

Related shows:

1. Repair, cleaning and refinishing old hardwood floors
2. Dangerous Tools
3. Home Improvement Tips, Rapid Fire

It’s time for another Handyguys tool challenge. On this show, the Handyguys take two very different compressors and run them through their paces. The listeners get to hear the difference between a small Makita MAC700 2 HP 2.6-gallon “hot dog” compressor and an older Porter-Cable compressor similar to the CPF4515 . Both compressors do a good job shooting framing nails into wood, but that is where the similarities end.

But does a handyguy or handygal really need a compressor? Is this something you need around the house? It all depends on the kind of work you will be doing. A compressor and pneumatic nailer are invaluable for trim work, crown molding, and framing. If you are going to finish your basement or have significant trim work around the house to complete, get a compressor. It will save a lot of time and hassle. For those weekend warriors, a compressor can’t be beat.

There are two basic varieties of compressors: oiled and oiless. The advantage of an oiless compressor is simpler maintenance — no oil or oil filter changes and no mess! However, the oiless compressors are generally very loud. While the oiled compressor is easier on the ear, they must be kept close to level at all times so the piston can be lubricated properly.

The other major differences between compressors is the tank size. The larger tank compressors can power tools that require large volumes of continuous air such as impact wrenches, grinders, and some paint sprayers. Pneumatic nailers use air in short bursts and can normally function well with smaller tanks. The smaller tanks are also much easier to move around. A large 20-gallon tank will not be very handy to move around the house to nail in baseboard trim.

So for about 90% of most household projects, the Makita MAC700 is the compressor to get. It is built like a tank, yet it does not blast your ear drums when the motor kicks in.

Once you get a compressor, you will need to get some pneumatic tools. There are hundreds of options. Normally you can just add some air tools as you need them. Typically you will start with a finish or framing nailer. For framing nailers, we like the full head framing nailer from Porter-Cable. There are generally two kinds of framing nails — clipped heads and round heads. The clipped heads have a “D” shape and allow you to get more nails within a clip. The downside is that some local codes do not allow the clipped heads. This is particularly true in hurricane prone areas. The round head nails look like typical nails.

Typical finish nailers include the 15-gauge angle nailer, the 16-gauge, and the 18-gauge. These nailers are great for baseboard trim, window casing, and crown molding. In addition, the 15-gauge can be used for hanging doors. The 15-gauge is the biggest, and it has a larger rectangular head which provides better holding power. Unfortunately it leaves a more drastic hole and requires more putty and sanding to hide the mark. The 18-gauge is the thinnest of the three and barely leaves a mark when it is nailed into finish trim. As a result you will not want to use it on heavy wood such as large crown molding.

For more information on compressors and nailers, tune in to this week’s Handyguys podcast.

Related shows:

1. How To Choose A Nail-gun
2. Attic Venting And Air Compressors