The Handyguys discuss the the energy saving task of caulking windows.

Announcements

Before we discuss caulking windows we would like to remind our listeners and viewers of our recent video production on replacing a flush valve.  In addition, we will be re-doing our “Fixing a Dishwasher” video in High Definition for additional clarity on the repair process. We hope to do a video showing some caulking techniques in the near future too.

Window Caulking

Handyguy Paul was asked by a friend “where do you caulk a window?”. That’s a pretty broad question. Is the window wood, vinyl or aluminum? Do You want to caulk it for aesthetics or because of drafts? We will assume drafts. Also, what is the siding material? new replacement windows in old frames? There are a lot of variables. We ramble on in the podcast discussing different places we caulk.

Vinyl windows and vinyl siding

Click to see a full sized image. Image © Andersen Corporation

Vinyl windows, if installed correctly shouldn’t need to be caulked in too many places. Caulking on the interior is mainly for aesthetics. You will caulk where the drywall meets the frame or the casing meets the frame. You can use some painters caulk on the inside where the window meets the casing or the drywall. If it was installed correctly there shouldn’t be a draft coming from this area.

Wood windows with wood siding

Click to see full sized image

These windows require a lot more maintenance. All gaps should be re-caulked. If caulking after painting or if you have natural wood, you use a clear caulk. If caulking before painting you should use paintable caulk rated for exterior use.

Replacement windows

Click to see a full sized image. Thanks to Champion Windows for providing this image.

Replacement windows are installed in existing wood frames. The windows come as a unit and should be caulked properly when installed. In situations with replacement windows, you have the area between the new window and the existing frame to keep caulk maintained as well as around any old trim.

Handyguy Tips

During a new segment to the show, the Handyguys each provide an important tip for the typical homeowner.

Thanks

Furnace filters are a critical component of your heating and cooling system.

Make sure they are changed regularly. We discuss the myriad of choices in furnace filters in this podcast.

The Handyguys group filters into three different categories, good, better and best. Whats best for one person may not be the best for another. The standard filters are good for most people. They permit the furnace to operate as it was designed. When selecting a filter you would typically replace with one equal in size and type to the filter already install on your furnace. This may be a a non-pleated fiber type filter. This type is also the least expensive, costing about $1.50 or $2.00 at the local True Value hardware store.

If you desire a replacement filter that has a higher MERV or MPR rating (see below for definitions) there are several choices at True Value. Go into the store with your measurements and pick one out. A higher rated filter will catch and filter more particulates from the air.

The high end filters will have electrostatic capabilities and can actually filter microscopic bacterias, smoke or other fine particulates from the air.

The industry provides ratings for filters.

MERV, or Minimum Efficiency Reporting Value, is a number from 1 to 16 that is relative to an air filter’s efficiency. The higher the MERV, the more efficient the air filter is at removing particles. At the lower end of the efficiency spectrum a fiberglass panel filter may have a MERV of 4 or 5. At the higher end, a MERV 14 filter is available.

MPR is a term used by 3M and stands for Microparticle Performance Rating. It is actually part of the MERV rating, and measures how efficient an air filter is at capturing particles between 0.3 and 1 micron in size, which make up 99% of the air’s particulate matter. Smoke, bacteria, and smog particles fall within this size range, so if filtering these out of the air is important to you, MPR is a good standard to examine. MPR is used to compare furnace filters to one another, and cannot accurately predict how a furnace filter will actually perform in your particular home environment. The higher the MPR, the more efficient the filter is at capturing these small particles.

Lastly – Don’t forget about our contest. We are giving away this awesome toolkit. Check out the details on how you can win by listening to Episode 87 of The Handyguys Podcast.

Win this tool kit!

Disclosure