The Handyguys June 26th, 2008

 

 Standard Podcast [20:54m]: Play Now | Play in Popup | Download

The Handyguys built a simple garden trellis of their own design and address listener questions

The handyguys built a simple garden trellis of their own design and decided to make plans available to anyone who wants them. Feel free to download the .pdf and pass it around to whoever may want it. Listen to the podcast for details on the design and construction. The trellis only uses one board and some screws. It will only take an hour or two to build.

Before the Handyguys get too deep into the trellis project they answer some listener questions.

First up is a question from Rob - Rob wants to remove a support pole from his basement. Don’t do it Rob. We share some tips for incorporating it in your design.

Second is a question from Roger about a white gritty substance in his hot water. Listen to the podcast for some suggestions. Its likely time for a new heater for Roger. Roger may find other useful information in our podcast entitled The Cold Water Heater

Third is a question from Tilo - Tilo is stuck as to how to run crown moulding around a window that goes up to the ceiling. The Handyguys recommend building a valance. We discussed nail guns and compressors in our episode entitled Compress It! Tilo, you may want to also give that a listen. A nail gun will make your project a lot easier.

Lastly listener Calster wants to know if they could glue a medicine cabinet to a large mirror in a bathroom. The Handyguys discuss some options but ultimately recommend removing the mirror. We will be talking about some new glues in an episode in a few weeks.But not likely something that will help Calister.

On to the Trellis

Tools and materials needed:

• Table saw
• Drill and bits
• Wood glue
• Spring clamps
• 5/4″ x 6″ x 8′ knot free cedar or similar
• 4″ exterior wood screws
• 1 1/4″ exterior wood screws
• bar clamps
• square

Steps to build:

1. Using a table saw, rip cedar into 3/4″ strips. You will be left with a small piece of wood about 3/16″ wide. You want that piece to come from the center of the board, not the edge.
2. Cut one of the slats into cross pieces as show on the next page
3. Cut your 3/16″ slat into eight 6″ pieces.
4. Assemble the base first as shown on page two. Use glue and screws. Pre-drill to prevent splitting. A bar clamp will help hold everything together while you are drilling and screwing.
5. Attach the top cross piece first. Use spring clamps to hold it while you drill and screw. Attach the center and outer two slats first then slats two and four. Attach with 1 1/4″ exterior wood screws. Use a square to ensure the first cross piece is square to the center slat.
6. Attach the remaining cross pieces in the same fashion and make sure they are square to the center slat.

We hope you find this to be a useful project. If you have any questions about it you can click on where it says comments right below this post and ask away.

If you have any other questions about your home or other DIY project you can always call us at 615-676-0877 or email The Handyguys at us@handyguyspodcast.com or use the contact form on the website.

• Handyguys Podcast Category
• Comments(0)

The Handyguys June 19th, 2008

 

 Standard Podcast [24:15m]: Play Now | Play in Popup | Download

The Handyguys complete their basement finishing series with an interview of a basement refinishing expert Roger German.

Part 2 of 2 of Roger German’s interview, Part 6 of the basement finishing series.

Brian and Paul complete their interview with basement remodeling expert Roger German. Mr. German is the author of Remodeling a Basement from the Taunton Press’ “Build Like a Pro” series of books. This is the second half of our interview.
In part 2 of the interview, Roger discusses the following:

• Basement Extras
• Lighting
• Drop Ceiling vs. sheet rock
• More on water mitigation

Thanks to listening to this interview with Roger German.

This post will conclude our 6 part series on basements. As always if you have any questions about any DIY or home improvement topics feel free to contact us. You may also comment on these posts.

In next weeks episode we will address several listener/reader questions as well as provide plans and give guidance on building and arbor for your garden.

• Handyguys Podcast Category
• Comments(0)

The Handyguys June 12th, 2008

 

 Standard Podcast: Play Now | Play in Popup | Download

The Handyguys complete their basement finishing series with an interview of a basement refinishing expert Roger German.

Part 1 of 2 of Roger German’s interview, Part 5 of the basement finishing series.

Brian and Paul are fortunate for the opportunity to interview an author and basement finishing expert. Roger German is the author of Remodeling a Basement from the Taunton Press “Build Like a Pro” series of books. Due to the length of this interview, it will be split up into two parts.

In part 1 of the interview, Roger discusses the following:

• How Roger got started with his book
• To DIY or not to DIY
• Mistakes seen
• You can do it cheap, do it fast, do it high quality - Pick two
• Some code issues
• HVAC, heating, venting, cooling options
• Steel vs wood studs
• Water mitigation

We wrap up the show talking about insulation, R values, vapor barriers, and mold prevention, etc. Thanks for listening. Buy the book or shop in our store to support the Handyguys Podcast. Next week will be part two of the interview.

• Handyguys Podcast Category
• Comments(1)

The Handyguys June 5th, 2008

 

 Standard Podcast [15:14m]: Play Now | Play in Popup | Download

The Handyguys discuss DIY appliance repair resources. In this episode Brian stops Paul from going too deep into his DIY washing machine repair without doing a little more research on the Internet.  Listen for the full story.

What Kind of Appliance Parts Can I Buy Online?

If you are planning any do it yourself appliance repair projects then you are likely shopping around for the best place to purchase your replacement appliance parts. Traditionally, some appliance parts were carried at your local hardware store or appliance store. If the store didn’t have what you were looking for then you could special order the parts that you needed. Often, that was expensive and the parts could take some time to come in leaving you without a working refrigerator, washer, dishwasher or other useful appliance.

Today there is another option. There are now internet websites that carry a large selection of parts for your household appliances. The best part about shopping internet websites is the large selection of parts that they carry and can ship to you immediately.

Below is a sampling of some common parts that are carried by online replacement stores.

• Washer parts: Pumps, Couplings, Agitator Kits, Knobs, Valves, Motors, Switches, Belts, Hoses and Gears
• Dryer parts: Heating Elements, Lint Filters, Belts and Rollers, Thermal Fuses, Thermostats and Blower Wheels
• Refrigerator parts: Water Valves, Defrost Heaters, Thermostats, Defrost Controls and Timers, Shelves, Drawers and Bins, Doors, Handles, Door Gaskets, Compressors and Relays
• Oven parts: Igniters, Bake and Broil Elements, Knobs, Grates, Drip Bowls, Burners, Valves and Thermostats
• Dishwasher parts: Dish racks and Baskets, Rollers, Wash Spray Arms, Gaskets, Door Seals, Pumps and Valves

These parts are carried for a large variety of manufacturers, like Whirlpool Parts, and many appliance models. It is worth checking an online appliance store if you have an appliance that is hard to find or older than 10 years since the online store might have the part that you need and save you the expense of replacing the entire appliance.

Although online replacement stores carry large amounts of inventory, it is still very simple to find the exact part that you need. Many websites allow you to search by appliance model number, replacement part number or description.

So, if you have an appliance that needs repair it is worth trying to find the part that you need at one of the online appliance stores that carry many parts.

The Handyguys talk about AppliancePartsPros.com
A few key features of  AppliancePartsPros.com are

• Live Help available on site via Live Chat, Toll Free Lines, or Email
• Very Fast Shipping with over 91% of in-stock orders delivered the next day
• Low Price Guarantee
• Over 1 million appliance parts in-stock
• Repair Forum available for those DIY’ers who need a little extra help.  The forum has thousands of questions and answers by professional repair technicians sorted by appliance type.
• Detailed model breakdowns and photos for help finding the correct part.  Example…http://www.appliancepartspros.com/partsearch/model.aspx?model_id=256714
• Experienced Staff with years of appliance parts knowledge
• They carry parts for all the major brands including Whirlpool, Kenmore, Maytag, GE, Fridgidaire, and more.  They also carry parts for the high-end, harder to find brands like Bosch, Dacor, Thermadore, and more.
• Website allows to search by Model Number, Part Description, or Part Number

The Handyguys would like to thank AppliancePartsPros.com for sponsoring this episode.

• Handyguys Podcast Category
• Comments(0)